Moderator: AdminGroup
Post Reply
- Print view
7 posts• Page 1 of 1
- CMDR_Harada
- Posts: 15
- Joined: Wed Oct 16, 2019 19:01
- Beenthanked: 3 times
MechWarrior 5 config file
- Quote
Postby CMDR_Harada » Sat Dec 14, 2019 9:19
If anyone wants/needs a good reference for Mechwarrior 5 HOTAS setup, I got it working with my Gladiator II / SCG handle. I had to manually rebuild the HOTAS file by hand.
There was a guide that showed how to get it working, but you had a load a bunch of other programs and drivers. According to the page you had to load a virtual joystick program that MW5 could read, and then map the unrecognized joystick to that, and then map the virtual joystick inside MW5 like you normally would. I found a way around that, so MW5 reads it directly.
Link to file that helped avoid the virtual joystick :
https://static.mw5mercs.com/docs/MW5Hot ... tation.pdf
WARNING : This was a major pain in the backside. It seems the config file is very sensitive to spaces and line feeds.
File attached, rename to HOTASMappings.Remap and drop in the right folder.
- Attachments
- HOTASMappings-Remap.doc
- (2.33 KiB) Downloaded 615 times
Top
- will
- Posts: 8
- Joined: Sun May 19, 2019 22:45
- Hasthanked: 53 times
- Beenthanked: 1 time
Re: MechWarrior 5 config file
- Quote
Postby will » Thu Dec 26, 2019 20:01
I started on mine, and kept running into problems with the axes getting stuck/stopped responding. I ended up leaving the HOTAS file very generic (just the list of buttons), and then using Joystick Gremlin for mapping the axes. Even with the additional trouble of getting Gremlin (and vjoy) installed, it was still easier to setup (and continue to tweak and configure) than that HOTAS file (you are not kidding that it's a major pain in the backside). It's just as well I went the Gremlin route, as it gives me a way to setup some more complicated mappings as well (macros for "F1 F1" and etc).
Top
- Caillin
- Posts: 107
- Joined: Mon Oct 26, 2015 6:04
- Hasthanked: 11 times
- Beenthanked: 29 times
Re: MechWarrior 5 config file
- Quote
Postby Caillin » Thu Dec 26, 2019 23:35
Yeah, I couldn't get any of the hat directions on my KG12 other than up to register by using the file, even triple checking for spaces and other potential formatting issues.
Top
- Orian
- Posts: 2
- Joined: Tue Jul 13, 2021 3:53
Re: MechWarrior 5 config file
- Quote
Postby Orian » Tue Jul 13, 2021 3:55
Has anyone had any luck setting up a dual gladiator premium hosas config for mech5? Not sure how to do the hotasmapping file with 2 identical joysticks (one left hand, one right hand). Any help would be much appreciated thank you!
Top
fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Hasthanked: 208 times
- Beenthanked: 1218 times
Re: MechWarrior 5 config file
- Quote
Postby fallout9 » Tue Jul 13, 2021 5:29
Just follow the walkthrough posted by CMDR_Harada, pretty straightforward. Unplug all USB devices and leave only one NXT so you could easily identify its VIP/PID, then do the same for the other one.
Top
- Orian
- Posts: 2
- Joined: Tue Jul 13, 2021 3:53
Re: MechWarrior 5 config file
- Quote
Postby Orian » Tue Jul 13, 2021 5:45
Thanks, but looking at this document:
https://docs.google.com/document/d/1jjT ... 5h6dlech56
Won't the vid & pid be identical since the sticks are identical?
edit: covered by this in the document
Because the HOTASMapping.Remap file identifies hardware based on vendor and product IDs, it is not currently possible to use two identical joysticks in a HOSAS configuration without third-party software. Assuming you are not using the hardware's accompanying app, the most elegant solution is to map one or both joysticks to a vJoy controller and add the latter to your config file.
Is there such software for these sticks? Or stick with vjoy?
Top
- VTMarik
- Posts: 5
- Joined: Sat Oct 10, 2020 23:39
Re: MechWarrior 5 config file
- Quote
Postby VTMarik » Tue Jan 18, 2022 20:30
Does anyone know how to add the THQ and SEM buttons/axes to this document? It can see the NXT now thanks to it but with the THQ and SEM out I really want to expand my options.
Top
Post Reply
- Print view
7 posts• Page 1 of 1
Return to “General discussions”
Jump to
- По русски
- Продукция ВКБ
- Информация
- По заказам
- Инструкции, практические советы и рекомендации
- Программное обеспечение
- Тех. поддержка
- Общий
- По сайту и форуму
- Про все и обо всем.
- In English
- Official announcements
- Manuals and Howtos
- VKB FSC Europe
- General discussions
- Technical Support
Who is online
Users browsing this forum: No registered users and 70 guests
